You will receive above data on below URL as result.
How we can perform the same on telit module GL865.
Earliest reply will be highly appriciable.
Thanks,
KD
Easy 🙂 Read in "Telit IP Eay User Guide" paragraph 3.5.1 (but don’t neglect the rest of the doc) "IP Easy- HTTP client application". Change all parameters in connection steps as required, then in HTTP request change the document, for example:
GET /servlet/tgtSendUrlDemo?response=0111111111111,2011-10-24,18:00:00 HTTP/1.1<cr><lf> Host: http://www.tulsagastechindia.com<cr><lf> Connection: keep-alive<cr><lf> <cr><lf>
Dear CB,
Thanks for your reply.
I have tried the same on my modem using RS Term tool thru serial port.
I configured my GPRS by sending commands suggested in this section.
When i send the below commands it results with ok instead of connect.
AT#SD=1,0,80,”www.telit.com”,0,0
Then i am not able to perrform below operation:
"Now following the HTTP protocol we ask for the homepage by sending the following
We use cookies to enhance your browsing experience and help us improve our websites. To improve our website, we carefully select third parties that use cookies to allow us to serve specific content and achieve the purposes set out in our cookie policy. For more information on how to make adjustments through your browser to the cookies being used on your device, please click Find Out More link. By closing this banner or continuing to browse our website, you agree to our use of such cookies. FIND OUT MORE
Hi,
I am working on GL865 Module & having the below query:
Can i send data along with URL?
For Example:
Sensing URL: (Copy this link & paste as web address)
http://www.tulsagastechindia.com/servlet/tgtSendUrlDemo?response=0111111111111,2011-10-24,18:00:00
Press Enter & yopu will get result as Done.
Receiving URL:
http://www.tulsagastechindia.com/servlet/tgtResponseResultDemo
You will receive above data on below URL as result.
How we can perform the same on telit module GL865.
Earliest reply will be highly appriciable.
Thanks,
KD
Easy 🙂 Read in "Telit IP Eay User Guide" paragraph 3.5.1 (but don’t neglect the rest of the doc) "IP Easy- HTTP client application". Change all parameters in connection steps as required, then in HTTP request change the document, for example:
GET /servlet/tgtSendUrlDemo?response=0111111111111,2011-10-24,18:00:00 HTTP/1.1<cr><lf>
Host: http://www.tulsagastechindia.com<cr><lf>
Connection: keep-alive<cr><lf>
<cr><lf>
Dear CB,
Thanks for your reply.
I have tried the same on my modem using RS Term tool thru serial port.
I configured my GPRS by sending commands suggested in this section.
When i send the below commands it results with ok instead of connect.
AT#SD=1,0,80,”www.telit.com”,0,0
Then i am not able to perrform below operation:
"Now following the HTTP protocol we ask for the homepage by sending the following
lines on the serial line:
GET / HTTP/1.1<cr><lf>
Host: http://www.telit.com<cr><lf>"
Note: My RS Term tool is not taking any command like Get/HTTP/1.1.
Pls advice how i can proceed further & where i can write my data in next commnads.
Pls revert back asap.
Rgds,
KD
The most common error, flow control mismatch: set AT&K0 for no flow control.
Dear CB,
Thanks..now i am able to write get/http/1.1 & press enter.
When i am writing below command:
at#sd=1,0,80,"www.teli.com",0,0,1
It results with ok & jst after 5 sec it result No carrier.
Pls also validate my command
get/http/1.1 & press enter
Thanks in advance.
Rgds,
KD
"www.telit.com"
Post a more complete log, you can enable logging in file in rsterm. Include as many diagnostics commands as you can.
Dear CB,
Pls see the attached log for your info.
Pls do needful.
Thanks,
KD
– set AT+CMEE=2
– set Log to file in rsterm, and select a file to log in; select from this file the part you want to post here, in text format
– don’t rush, read "Telit AT Commands Reference Guide" and "Telit IP Easy User Guide", don’t skip chapters because this will bite later
– use online socket mode until you catch the move, then you can go further with command mode
Hi,
I am following the steps correctly but not able to connect.
Pls see the attached log & do needful.
I am facing "NO CARRIER" at the ened of connect.
Pls advice.
Thanks,
KD
Please do it, then after CONNECT send the HTTP request.
Hi,
I am following the steps correctly but not able to connect.
Pls see the attached log & do needful.
I am facing "NO CARRIER" at the ened of connect.
Pls advice.
Thanks,
KD